The URL can be used to link to this page

Home My WebLink AboutMAX MEDIUM DENSITY CCTDS V1.1 April 1,2020 MAX Insulation of the Future Medium Density • Closed Cell Spray Foam Insulation TECHNICAL DATA SHEET Material Specication Criteria | Project Submittal Data Thermoseal MAX ThermoSeal MAX is a two component, semi-rigid, medium density, 1.7 lb closed cell polyurethane foam insulation system which simultaneously insulates and air-seals your building structure. Thermoseal MAX requires the use of an “A” component (ISO) and a blended “B” component (RESIN), which contains ZERO ozone depleting catalysts, polyols and re retarding materials. ThermoSeal MAX is designed for residential, commercial, and industrial building applications to make structures more energy ecient, quieter, healthier and more comfortable. ThermoSeal MAX is applied as a liquid spray and lls all building cavities completely sealing all cracks, crevices, and voids where air loss and inltration are most common. Physical Properties Property Value Test Method R-Value 6.9 @ 1”/21.0 @ 3”ASTM C 518 Core Density 1.7 LB / Cubic Foot ASTM D 1622 Closed Cell Content >= 90%ASTM D 2586 Water Vapor Transmission - Permeance Perms: .8 @ 1” / .23 @ 3.5”ASTM E 96 Tensile Strength (PSI)50 ASTM D 1623 Dimensional Stability < 9%ASTM D 2126 Fire Properties Property Value Test Method Surface Burning Charateristics Class 1 Pass <25 / <450 ASTM E 84• Flame Spread / Smoke Index Ignition Barrier ICC- ES AC377 Appendix X Thermal Barrier NFPA 286 • In Process • In Process Building Code Certications Evaluation Report TBD Thermoseal, llc Po Box 32 New Canaan, CT. 06840 www.ThermoSealUSA.com 800.853.1577 info@ThermosealUSA.com IAPMO Compressive Strength (PSI)43 ASTM D 1621 Air Leakage Rate Zero (0) ft3/s.ft2 @ 75Pa ASTM E 283 Sound Transmission Coecient 41 ASTM E-90-85/E 413 UL 1715 TDS V1.1 April1, 2020 DISCLAIMER: To the best of our knowledge, all technical data contained herein is true and accurate as of the date of issuance and subject to change without prior notice. User must contact Thermoseal, llc to verify correctness before specifying or ordering. We guarantee our products to conform to the quality control standards established by Thermoseal, llc. We assume no responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of the product. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY THERMOSEAL USA EXPRESSED OR IMPLIED; STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Recommended Processing Parameters Recirculation Target Do not recirculate. Gradually warm drums to 77˚F prior to use. Primary Heater Target (Initial) 125˚F 125˚F 52˚C Primary Hose Target (Initial)52˚C Target Processing Pressure 1200 psi 8274 kPa Substrate & Ambient Temp >14˚F (Winter)/ >45 ˚F (Summer) >-10˚C (Winter)/ >7 ˚C (Summer) Moisture Content of Substrate <20%<20% • Must be clean and free of dust and debris Moisture Content of Concrete <10%<10% TECHNICAL DATA SHEET Material Specication Criteria | Project Submittal Data Thermoseal, llc Po Box 32 New Canaan, CT. 06840 www.ThermoSealUSA.com 800.853.1577 info@ThermosealUSA.com Storage and Processing Information Thermoseal MAX Liquid Component Properties Property A Side - PMDI B Side- Thermoseal MAX Color Brown Amber Viscosity @ 77˚F (25˚C)185 - 230 cps 400-520 cps Specic Gravity 1.25 1.17 - 1.19 Storage Temperature 50˚F-75˚F ( 10˚C-24˚C)50˚F-75˚F ( 10˚C-24˚C) Mixing Ratio (By Volume)1:1 1:1 • Of unopened drums stored within specied range Shelf Life 1 Year 18 Months MAX Insulation of the Future Processing - Application processing temperatures can vary and are dependent upon indoor ambient temperature, outdoor ambient temperature, substrate temperature, humidity, elevation, substrate type, equipment, and other factors. While manufacturing polyurethane foam plastic on site, the applicator must continuously observe the characteristics of the sprayed foam and adjust the processing temperatures and pressures to maintain optimal cell structure, adhesion, and overall foam quality. It is the sole responsibility of the applicator to manufacture Thermoseal polyurethane foam plastic on-site within our specications. When applying Thermoseal, all substrates must be 10 ˚F degrees above the dew point and free of all debris including frost, oil, rust, dust, or other debris. The equipment being used must be set to deliver a consistent 1:1 ratio by volume and must be capable of achieving at least 1200 psi and the target processing temperatures outlined in this manual. To maintain warranty status on all Thermoseal products, the Applicator’s Thermoseal Training Certicate must be current. Thermoseal Training is free and can be conducted on our website at http://www.ThermosealUSA.com.