HomeMy WebLinkAbout01-4339.13-In-Place-Mockups_Rev_0Dennis Yarmouth Intermediate Middle School January 19, 2021
Dennis Yarmouth Regional School District 100% Construction Documents
Perkins Eastman DPC, project #71011
IN-PLACE MOCKUPS
01 4339.13 - 1
SECTION 01 4339.13
IN-PLACE MOCKUPS
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and other Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section includes general requirements for in-place mockups required by individual specification
Sections and Drawings.
B. Related Requirements:
1. Section 01 4000 “Quality Requirements” for definition of mockups and for administrative
and procedural requirements for quality assurance and quality control.
2. Section 01 4339 “Mockups” for exterior wall mockups that consist of Work specified in
more than one Section of the specifications.
3. Section 01 7329 “Cutting And Patching” for cutting and patching requirements for repair
and restoration of construction disturbed by the construction of rejected in-place
mockups.
4. Division 02 through 33 Sections for:
a. Specific requirements and materials applicable to in-place mockups.
b. Requirements for field testing and inspection of in-place mockups to determine
compliance with specified requirements.
1.3 DEFINITIONS
A. In-Place Mockups: In-place mockups are full-size physical assemblies that are mockups
constructed “in-place” in the building and not intended to be disposable unless rejected as
non-compliant. In-place mockups are constructed to verify selections made under Sample
submittals; to demonstrate aesthetic effects and, where indicated, qualities of materials and
execution; to review coordination, testing, or operation; to show interface between dissimilar
materials; and to demonstrate compliance with specified installation tolerances. In-place
mockups are not Samples. Unless otherwise indicated, approved in-place mockups establish
the standard by which the Work will be judged
1.4 IN-PLACE MOCKUPS, GENERAL REQUIREMENTS
A. Intent of In-Place Mockups: Provide in-place mockups to obtain Owner's and Architect's
approval of in-place mockups prior to production work and to identify and resolve problems, if
any, before proceeding with the Work. The intent of in-place mockups is to identify and resolve
problems, if any, early-on to minimize remedial work.
B. Lighting: Provide final lighting or accurate simulation of final lighting before Owner's and
Architect's review of in-place mockups. If final lighting or accurate simulation of final lighting is
not provided, Owner and Architect will only provide conditional approval subject to final approval
Dennis Yarmouth Intermediate Middle School January 19, 2021
Dennis Yarmouth Regional School District 100% Construction Documents
Perkins Eastman DPC, project #71011
IN-PLACE MOCKUPS
01 4339.13 - 2
when reviewed under final lighting. Conditionally approved in-place mockups may be rejected
after being reviewed under final lighting.
C. Rejected In-Place Mockups: Owner or Architect may reject in-place mockups for subjective or
discretionary decisions reguarding appearance. Owner and Architect may reject in-place
mockups even if smaller "selection samples" or "verification samples" were previously
approved. Remove and replace rejected in-place mockups at no additional cost to Owner until
acceptable appearance is achieved. There is no limit on the number of rejected and
replacement in-place mockups that may be required.
D. Additional Requirements for In-Place Mockups:
1. Do not assume in-place mockups will be approved.
2. Do not order materials in production quantities until in-place mockups are approved.
3. Do not proceed with production work until in-place mockups are approved.
4. Provide in-place mockups at the earliest possible time.
5. Locate in-place mockups where indicated or pre-approved by Architect.
6. Preserve and protect in-place mockups as examples of accepted work.
7. Do not alter or destroy approved in-place mockups.
8. Incorporate approved in-place mockups into the final work.
9. Make production work visually match approved in-place mockups.
PART 2 - PRODUCTS (not applicable)
PART 3 - EXECUTION (not applicable)
END OF SECTION