HomeMy WebLinkAbout10-2116-Plastic-Shower-and-Dressing-Compartments_Rev_1Dennis Yarmouth Intermediate Middle School January 19, 2021
Dennis Yarmouth Regional School District 100% Construction Documents
Perkins Eastman DPC, project #71011
PLASTIC SHOWER AND DRESSING COMPARTMENTS
10 2116.19 - 1
SECTION 10 2116.19
PLASTIC SHOWER AND DRESSING COMPARTMENTS
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section includes solid-plastic compartments.
B. Related Requirements:
1. Section 01 8113.13 “Sustainable Design Requirements” for general requirements and
procedures for compliance with certain USGBC LEED prerequisites and credits.
2. Section 06 1000 "Rough Carpentry" for blocking.
3. Section 09 2216 "Non-Structural Metal Framing" for blocking.
4. Section 10 2113.19 “Plastic Toilet Compartments.”
5. Section 10 2800 "Toilet, Bath, and Laundry Accessories" for accessories mounted on
solid-plastic compartments.
6. Division 22 Sections "Plumbing" for shower heads, valves, and controls.
1.3 ACTION SUBMITTALS
A. Make Submittals in accordance with Section 01 3300 “Submittal Procedures.”
B. Product Data: For each type of product.
1. Include construction details, material descriptions, dimensions of individual components
and profiles, and finishes.
C. Sustainable Design Submittals:
1. Recycled Content: Provide manufacturers’ product documentation that includes recycled
content claims for the products contributing towards compliance. Claims must conform to
the definition in ISO 14021-1999, Environmental Labels and Declarations, Self-Declared
Environmental Claims.
a. Complete "LEED Materials Documentation Sheet" with MRc3 Option 2 information
for products with recycled content installed in the building.
D. Shop Drawings: For shower and dressing compartments.
1. Include plans, elevations, sections, and attachment details.
2. Show locations of cutouts for compartment-mounted accessories.
3. Show locations of centerlines of drains.
E. Samples for Verification: For the following products, in manufacturer's standard sizes unless
otherwise indicated:
1. Each type of material, color, and finish required for compartments, prepared on 6-inch-
square Samples of same thickness and material indicated for the Work.
Dennis Yarmouth Intermediate Middle School January 19, 2021
Dennis Yarmouth Regional School District 100% Construction Documents
Perkins Eastman DPC, project #71011
PLASTIC SHOWER AND DRESSING COMPARTMENTS
10 2116.19 - 2
2. Each type of hardware and accessory.
3. Curtain Fabric: 12-inch- square swatch or larger as required to show complete pattern
repeat, from dye lot used for the Work, with specified treatments applied. Mark top and
face of material.
1.4 INFORMATIONAL SUBMITTALS
A. Product Certificates: For each type of shower and dressing compartment.
1.5 CLOSEOUT SUBMITTALS
A. Maintenance Data: For shower and dressing compartments to include in maintenance
manuals.
1.6 MAINTENANCE MATERIAL SUBMITTALS
A. Furnish extra materials, from the same product run, that match products installed and that are
packaged with protective covering for storage and identified with labels describing contents.
1. Door Hinges: Two door hinges with associated fasteners.
2. Latch and Keeper: Two latches and keepers with associated fasteners.
3. Clothing Hook: Two clothing hooks with associated fasteners.
4. Door Bumper: Two door bumpers with associated fasteners.
5. Door Pull: Two door pulls with associated fasteners.
6. Fasteners: 10 fasteners of each size and type.
7. Curtain Rod: Two curtain rods with associated fasteners.
8. Curtain Hooks: Five curtain hooks.
9. Soap Holder: Two soap holders with associated fasteners.
10. Seat: One seat with associated fasteners.
1.7 FIELD CONDITIONS
A. Field Measurements: Verify actual locations of fixtures, drains, walls, columns, ceilings, and
other construction contiguous with shower and dressing compartments by field measurements
before fabrication.
PART 2 - PRODUCTS
2.1 LEED REQUIREMENTS
A. Recycled Content: Provide products with the maximum recycled content possible. Minimum
recycled content 20 percent.
2.2 PERFORMANCE REQUIREMENTS
A. Fire Performance: Tested according to, and pass the acceptance criteria of, NFPA 286.
Dennis Yarmouth Intermediate Middle School January 19, 2021
Dennis Yarmouth Regional School District 100% Construction Documents
Perkins Eastman DPC, project #71011
PLASTIC SHOWER AND DRESSING COMPARTMENTS
10 2116.19 - 3
B. Regulatory Requirements: Comply with applicable provisions in 521 CMR, Massachusetts
Architectural Access Board (AAB), for shower and dressing compartments designated as
accessible.
2.3 SOLID-PLASTIC COMPARTMENTS
A. Basis-of-Design Product: Subject to compliance with requirements, provide Eclipse Partitions
by Scranton Products, or a comparable product by one of the following or equal:
1. Bradely Corporation (Bradmar Partitions).
2. General Partitions (Eastern MAX Style).
3. Hadrian Inc. (Elite MAX).
4. Global Partitions (Alpac Classic).
B. Configuration: Shower and dressing compartments as indicated on Drawings.
C. Enclosure Style: Floor-mounted, overhead braced.
D. Panel and Pilaster Construction: Solid, high-density polyethylene (HDPE) panel material, not
less than 1 inch thick, seamless, with eased edges and with homogenous color and pattern
throughout thickness of material.
1. Waterproof and nonabsorbent, with self-lubricating surface, resistant to marks by pens,
pencils, markers, and other writing instruments.
2. Edges: Shiplap.
3. Heat-Sink Strip: Manufacturer's standard, continuous, stainless steel strip fastened to
exposed bottom edges of solid-plastic components to hinder malicious combustion.
4. Color and Pattern: As selected by Architect from manufacturer’s full range.
E. Doors and Dividing Panels: 62 inches high and mounted at 12 inches above the finished floor.
F. Metal Posts: 82-3/4 inches high, heavy duty extruded aluminum, clear anodized finish, fastened
to foot with stainless steel tamper resistant screw.
G. Hidden Shoe (Foot): One-piece molded polyethylene invisible shoe inserted into metal post and
secured to metal post with stainless steel tamper resistant screw.
H. Headrail Cap and Corner Cap: One-piece molded polyethylene secured to metal post with
stainless steel tamper resistant screw; adjustable to level headrail to finished floor.
I. Wall Brackets: Continuous heavy duty extruded aluminum, clear anodized finish, inserted into
slotted panel and fastened to panels with stainless steel tamper resistant screws.
1. Type: Double ear bracket aluminum.
2. Length: 65 inches.
J. Headrail: Heavy duty extruded aluminum, designer anti-grip design, clear anodized finish,
fastened to headrail bracket with stainless steel tamper resistant screw and to headrail cap or
corner cap with stainless steel tamper resistant screw.
1. Headrail Brackets: Heavy duty extruded aluminum, clear anodized finish, secured to wall
with stainless steel tamper screws.
2.4 MATERIALS
A. Aluminum Castings: ASTM B26/B26M.
Dennis Yarmouth Intermediate Middle School January 19, 2021
Dennis Yarmouth Regional School District 100% Construction Documents
Perkins Eastman DPC, project #71011
PLASTIC SHOWER AND DRESSING COMPARTMENTS
10 2116.19 - 4
B. Aluminum Extrusions: ASTM B221.
C. Stainless Steel Sheet: ASTM A240/A240M or ASTM A666, Type 304, stretcher-leveled
standard of flatness.
D. Stainless Steel Castings: ASTM A743/A743M.
2.5 ACCESSORIES
A. Door Hardware and Accessories: Manufacturer's standard design, heavy-duty, operating
hardware and accessories. Mount to panels with through-bolts.
1. Hinges: Manufacturer's standard, paired, self-closing type that can be adjusted to hold
doors open at any angle up to 90 degrees, allowing emergency access by lifting door.
2. Latch and Keeper: Manufacturer's standard, surface-mounted latch unit designed for
emergency access and with combination rubber-faced door strike and keeper. Provide
units that comply with regulatory requirements for accessibility at each compartment,
accessible or not.
3. Clothing Hooks: Manufacturer's standard clothing hooks in each dressing
compartment; include one combination hook and rubber-tipped bumper at inswinging
doors, sized to prevent door from hitting wall panel or compartment-mounted
accessories.
4. Door Bumper: Manufacturer's standard, rubber-tipped bumper at outswinging doors.
5. Door Pull: Manufacturer's standard unit at outswinging doors that complies with
regulatory requirements for accessibility. Provide units on both sides of doors at
compartments designated as accessible.
B. Headrail with Hooks: Manufacturer's standard, continuous, extruded-aluminum headrail or cap
with curtain hooks running in concealed track; with antigrip profile; in manufacturer's standard
finish.
C. Curtain Rod with Hooks: Manufacturer's standard, 1-inch- diameter, stainless steel curtain rod
with matching hooks.
D. Curtain: Flame-resistant, polyester-reinforced vinyl fabric that is stain resistant, self-sanitizing,
antistatic, antimicrobial, and launderable to a temperature of not less than 90 deg F.
1. Flame Resistance: Passes NFPA 701 tests when tested by a testing and inspecting
agency acceptable to authorities having jurisdiction.
2. Labeling: Identify fabrics with appropriate markings of applicable testing and inspecting
agency.
3. Curtain Grommets: Two-piece, rolled-edge, rustproof, nickel-plated brass; spaced not
more than 6 inches o.c.; machined into top hem.
4. Width: Minimum 12 inches wider than opening.
5. Length: Where curtain extends to a floor surface, size so that bottom hem clears finished
floor by not more than 1 inch and not less than 1/2 inch above floor surface. Where
curtains extend to a shower-receptor curb, size so that bottom hem hangs above curb
line and clears curb line by not more than 1/2 inch.
6. Color and Pattern: As selected by Architect from manufacturer's full range.
E. Soap Holder: Surface-mounted, seamless stainless steel soap dish.
F. Seats: Manufacturer's standard, panel-mounted or wall-mounted benches.
1. Material: Solid phenolic.
2. Operation: Folding.
Dennis Yarmouth Intermediate Middle School January 19, 2021
Dennis Yarmouth Regional School District 100% Construction Documents
Perkins Eastman DPC, project #71011
PLASTIC SHOWER AND DRESSING COMPARTMENTS
10 2116.19 - 5
3. Finish: Match enclosure panels.
G. Anchorages and Fasteners: Manufacturer's standard, exposed fasteners of stainless steel,
chrome-plated steel, or solid brass, finished to match the items they are securing; with theft-
resistant-type heads. Provide sex-type bolts for through-bolt applications. Use countersunk,
flush-type bolt heads or otherwise make fasteners inconspicuous if exposed on opposite side of
panel from hardware or accessory item. For concealed anchors, use stainless steel, hot-dip
galvanized steel, or other rust-resistant, protective-coated steel.
2.6 FABRICATION
A. Overhead-Braced Compartments: Manufacturer's standard, corrosion-resistant supports,
leveling method, and anchors at pilasters and walls to suit floor and wall conditions. Provide
shoes at pilasters to conceal supports and leveling method.
B. Door Sizes and Swings: Unless otherwise indicated, provide 24-inch- wide, inswinging doors
for standard shower and dressing compartments, and 36-inch- wide, outswinging doors with a
minimum 32-inch- wide, clear opening for compartments designated as accessible.
PART 3 - EXECUTION
3.1 INSTALLATION
A. Comply with manufacturer's written installation instructions. Install compartments rigid, straight,
level, and plumb. Secure compartments in position with manufacturer's recommended
anchoring devices.
1. Clearances for Dressing Compartments: Maximum 1/2 inch between pilasters and
panels; 1 inch between panels and walls.
2. Full-Height (Continuous) Brackets for Dressing Compartments: Secure panels to walls
and to pilasters with full-height brackets.
a. Locate bracket fasteners so holes for wall anchors occur in masonry or tile joints.
b. Align brackets at pilasters with brackets at walls.
B. Overhead-Braced Compartments: Secure pilasters to floor, and level, plumb, and tighten. Set
pilasters with anchors penetrating not less than 1-3/4 inches into structural floor unless
otherwise indicated in manufacturer's written instructions. Secure continuous headrail to each
pilaster with no fewer than two fasteners. Hang doors to align tops of doors with tops of panels,
and adjust so tops of doors are parallel with overhead brace when doors are in closed position.
C. Curtains: Install curtains to specified length, and verify that they hang vertically without stress
points or diagonal folds.
3.2 ADJUSTING
A. Curtain Adjustment: After hanging curtains, test and adjust each track or rod to produce
unencumbered, smooth operation. Steam and dress down curtains as required to produce
crease- and wrinkle-free installation. Remove and replace curtains that are stained or soiled or
that have stress points or diagonal folds.
B. Hardware Adjustment: Adjust and lubricate hardware according to hardware manufacturer's
written instructions for proper operation. Set hinges on inswinging doors to hold doors open
Dennis Yarmouth Intermediate Middle School January 19, 2021
Dennis Yarmouth Regional School District 100% Construction Documents
Perkins Eastman DPC, project #71011
PLASTIC SHOWER AND DRESSING COMPARTMENTS
10 2116.19 - 6
approximately 30 degrees from closed position when unlatched. Set hinges on outswinging
doors to return doors to fully closed position.
END OF SECTION