The URL can be used to link to this page

Home My WebLink About23-A046 970 Route 6ATOWN OF YARMOUTH 1146 ROUTE 28, SOUTH YARMOUTH. MA 02664-4451 Telephone (508) 398-2231 Ext. 1292--Fax (508) 398-0836 HIGHWAY HISTORIC DISTRICT COMMITTEE APPLICATION FOR CERTIFICATE OF APPROPRIATENESS Application is hereby made for issuance of a Certificate of Appropriateness under Section 6 of Chapter 470, Acts of 1973 as amended, for proposed work as described below & on plans, drawings, photographs, & other supplemental info accompanying this application. PLEASE SUBMIT 4 copies OF SPEC SHEET(S), ELEVATIONS, PHOTOS, & SUPPLEMENTAL INFORMATION. Check Alf Categories ThatApg@ a C04rQk a type of Building: Commercial —y" Residential 1) Exterior Building Construction: New Building Addition VAlterations Reroof Garage Shed Solar Panels Other: 2) Exterior Painting: Siding Shutters Doors Trim Other: 3) Signs/Billboards: New Sign Change to Existing Sign 4) Miscellaneous Structures: Fence Wall Flagpole Pool Please type or print legibly: Other: Address of proposed work: 970 Route 6A Yarmouth Port MA 02675 Map/Lot # 151 / 80.3 Owner(s): Peter & Carol Keefe Phone #: 774-994-0529 All applications must be submitted by owner or accompanied by letter from owner approving submittal of application. Mailing address: 970 Route 6A Yarmouth Port MA 02675 Year built: 1995 Email: pckeefel207@gmail.com Preferred notification method: Phone _Email Agent/contractor: Sand Dollar Customs / Walter R, Waren, Jr Mailing Address: 259 Great Western Rd Unit B South Dennis MA 02660 Phone #: 508-694-5618 Email: office@sanddollarcustoms.com Preferred notification method: Phone V Email Description of Proposed Work. Master bedroom addition, and one garage bay addition. Re -roofing, re -siding, new windows and doors throughout. Signed (Owner or agent): _ L!/, /_1 Gt'/a�, Date: 4/4/23 ➢ Ownedcontractodagent is aware that a permit is required from ttfe Building Department. (Check other departments, also.) D If application is approved, approval is subject to a 10-day appeal period required by the Act. ➢ This certificate is good for one year from approval date or upon date of expiration of Building Permit, whichever dale shall be later. ➢ All new construction will be subject to inspection by OKH. OKH-approved plans MUST be available on -site for framing & final inspections. Rcvd Date: `7 ll qh Amount "[ r Cash/CK #: t Rcvd by: t-ti 51 45 Days: Date Signed: Approved Approved with Modifications Denied Reason for Denial: Signed: APPLICATION #: ?-5' r ' — GENERAL SPECIFICATION SHEET Project Address: FOUNDATION: Material: Y Concrete slab on 50 ft vapor harrier an 6" compacted gravel base Expos re (Not to exceed 18"): CHIMNEY: Material/Color: existing GUTTERS: Material/Color: White Aluminum ROOF: Material: Asphalt Pitch (7112 min) Height to Ridge SIDING: Material/Style: Front: Cedar Shake Sides/Rear: Cedar Shake Color: Front: Cape Cod Grey Sides/Rear: Unfinished TRIM: All windows & doors to be trimmed with: Material: Azek Composite 1x 4 0(Circle one.) Color: White DOORS: Qty: 2 Material: Fiberglass Color: Heritage Red Style/Size (if not listed/shown on elevations): Also, 1 slider door, Vinyl STORM DOORS: Qty: 2 Material: Aluminum Color: White GARAGE DOORS: Qty: 2 MatT Galvanized Steel Style: Colonial Color: White WINDOWS: !side:: Front: 11 Left: 1 Right: 5 Rear: 5 color: Black Manufacturer/Series: Harvey Classic Material: Vinyl -New Construction Grilles (Required): Pattern (6/6, 2/1, etc.) 6/6 Grille Type: True Divided Lite: Snap -In: Between Glass: Permanently Applied: Exterior Interior STORM WINDOWS: Qty: Material: Color: SHUTTERS: MatT Style: Paneled Louvered Color: SKYLIGHTS: Qty: Fixed Vented Size Color: Color: Moire Black COLOR CHIPS CCEIVC Q APR 14 2023 rAHM001 h DECK: Size: Decking MatT Color: Railing MatT Style: Color: WALLSIFENCES* (Max 6' height): Height: MatT Style: Color: (Show running footage & location on plot plan.) *Finished side of fence must face out from fenced in area. UTILITY METERSIHVAC UNITS: Location: LIGHTS: Qty: Style: Location(s): LIGHT POSTS: City: _ Location(s): Additional information: Material: Screening: Color: Color: 2-General APPLICATION #: Telephone (508) 398-2231 Ext. 1292 Fax (508) 398-0836 OLD KING'S HIGHWAY HISTORIC DISTRICT COMMITTEE 45-DAY TIMEFRAME HIECFIVED WAIVER APR 14 2023 ^. _ r Hn;vlui 1 r Application #: 23 - 4� Project Address: 970 Route 6A Yarmouth Pork MA 02675 Application Received Date: / h 45 Day Decision Deadline: I/We, the undersigned owner, contractor, or agent, do hereby waive the 45-day timeframe for a determination on our application for a Certificate of Appropriateness/Demolition/Exemption by the Old King's Highway Historic District Committee for the following project: Date: 4111I23 Signed: (see attached authorization) Owner Peter & Carol Keefe Owner (t,)M ..� Contractor/Agent TOWN OF YARMOUTH OLD KING'S HIGHWAY HISTORIC DISTRICT COMMITTEE 2023 MEETING SCHEDULE L� -?� /)7)qJ� TOWN OF YARMOUTH OLD KING'S HIGHWAY HISTORIC DISTRICT COMMITTEE ABUTTERS' LIST Applicant's (Owner) Name: 4,ff -�C?w lue-re Property Address/Location: cf 70 Hearing Date: : �J;- r , �?3 Notices must be sent to the applicant and abutters (including owners of land on any public or private street or way) whose property directly abuts or is across the street from the applicant. The OKH Office will send out notices using the addresses as they appear on the most recent applicable tax list. Note: Instructions for obtaining the abutters Map and Lot numbers can be found on the Old King's Highway Department page on the Town website: www.varmouth.ma.us Map Number Lot Number Applicant Information Abutter Information: GGEIVED APR 14 2023 YARMOUTh 3O 1 Y7 a- � I 13F � qa Ti (72 '� Application #: ;� 3 I'IW4 L 8.2018 3 TOWN OF YARMOUTH 1146 ROUTE 28, SOUTH YARMOUTH, MASSACHUSETTS 02664-4451 % �� RECEIVED APR 14 2023 OLD KING'S HIGHWAY 0 1 I.[ o0 F �W SC U o fAj fA u N m I ZII _ V! 1Ixa 114< 4 iJ T gg iqA' TF�' !§]2] §(\\k§/)( §2e!!§2!a §§)k)) ! RECEIVED § 618.§ § ' APR 14 2023 0 Y HMOU h ( 0 § OLD KNG'SHIGHWAY g A§ «� }k z . .% :5 `u, � \-----2 -- - ----s � - r «! �- |� d) � z----------- --o � � |'§ I �� i -- — .a.w. ---------------- —_-- -- ---------------l�� £e % h� ; /� \-----?---� i | )k Ls s RECEIVED S � �/ APR 14 2023 }a, . kn YAHm Ulh OLD mNGs HIGHWAY z\ ! §§/ $�7 0 ) 2 � ,� \( !r /i[ (/ ..t.| h ; ||| !,§ � | t \ 2 § r § � | FM \ - . � ��—�� ------------ -------------------------------- z /vJ 9 LLB APR ". 4 ?Q%3 Q I d HhkV10U 1 LD KING'S HtiGH'� Q z I a I \ I Ir AD all UUU.7 (4�I y g O Ll avolJ v 11JJ LON64ELLOW Sx F 14 j W ti U ;rp _@ I 013 LL EC k O - }� ono OEORGE --------------------- r�- - I" r , � r I - _ Fm , 3-b RFCFI Y GD APR. 4 2023 r nMVIOUTh wa RFOEIVED A F R 14 2023 r ,'AryM OUTh J � '�4 PFCEIVED APR 14 2023 -iriMOUTh 0LD KING'S HIGHWAY IN iAw heritage red &njem,n Moore benjamin moore CHANTILLY LACE OC-65 HC-181 SBC CEDAR SHINGLES IN CAPE COI] GRAY RFeEIVED AFR 14 2023 imn,vIC]UTh 9�, .. /lmq,� Black Windows, White Trim, CC Gray Shingles Roof to Match Existing REMIVED APR 4 2023 YAHIVJOUTH o93--At� Variable width 3-7/16" to iz" FACE From 15-1/2" to 16" Nail tine 6-1/8" 90° i1- Image not to Scale 1/16' SIDE -0-I If-- 3/8" RECEIVED APR 1. 4 2023 SBC YAHIVIOU'1 h,: CEDAR OLD KINGS HIGHWAY GENERAL SPECIFICATIONS Thuj[r occidentalis Eastern White Cedar SBC standards exceed ::SA 0118.2-1 08 (C20 18) ;BC cedar shingles are graded Zn both faces Solid Weathering Agent Primer Semi -Transparent Naturaltone cedar Sidewall No imperfection 3/8" 3-7/16" to 12" 16" Siding Select AB on the exposed surface. (9,5 mm) (87 mm to 306 mm) (406 mm) Blend of grade Extra A and Clear B optimizing shingles width DEMANDOTHER GRADES AVAILARL E ON FACTORY STAIN APPLICATION - STAINED ON ALL SIDES Solid [lipping PPG Machinecoat� o 100/ acrylic Hot Air/Oven 1 Coat - Io Years z Coats - 25 Years Semi -transparent Dipping PPG Machinecoat" 100% acrylic Hof Alr/Oven 1 Coat - Years 5 — Pro -Prime Dipping PPGMachinecoat" 100% acrylic Hot Air/Oven N/A -----.--- - - _ ---------- ---------__ 30 years Enviro Bleach Dipping Hybrid Hot Air/Oven .._- - -- ----- N/A — against wood decay Weathering Stain Impregnation ail Air circulation N/A Bleaching OIL Impregnation OR Air circulation N/A Naturaltone Cedar Impregnation ail Air circulation N/A D�sj 'Against flaking and peeling. See more details on SBCcedar.com in the Warranty section f ■o■ in COVERAGETABLE - 4" (102 mm) 20 sq.ft (1.9 m2) 4-1/2" (114 mm) T -- -. 22 sq.ft (2.1 m2) -- 51I' (127 mm) 26 sq.ft (2.3 m2) 'Maximum recommended To calculate the number of boxes needed, add 5% to the area to cover. MANUFACTURING • Cedar logs are selected from responsible forest management based on the best quality and size available. • Use of stellite-tipped blades for a smoother surface and minimized raised grain. Laser -guided precision edging for superior quality. • Use of artificial vision system to measure and recut each shingle with an accuracy of 1/64" (0.4 mm) to obtain perfectly parallel sides and perpendicular butt. Embossed nailing line at 6-1/8" (156 mm) from the butt on one side for easy fasteners alignment. Dehumidification drying process between 10%and 14%moisture content to optimize wood stability and maximize coating adhesion. FACTORY -STAINING APPLICATION METHOD Dipping (acrylic products): Exclusive dipping process followed by hot air drying to ensure unparalleled uniformity and a thicker film on the exposed surface. Impregnation (oil -based products): Exclusive impregnation flood coat and brushing process followed by ambient air circulation to ensure maximum penetration into the wood. TYPE OF FINISH DETAILS PPG Machinecoat° 100% acrylic: Superior quality finish for factory application under optimal conditions; Its flexible film resists peeling and flaking. Enviro Bleach: Hybrid low VOC weathering agent that contains fungicide and wood preservative agents. Its hybrid technology delivers the look of oil -based products with the performance and environmental benefits of water -based coatings. Weathering stain & Bleaching oil: Linseed oil -based weathering agent that penetrates the wood and accelerates the cedar natural aging process. • Naturaltone Cedar: PPG/Olympic Maximum® 57503 oil -based toner that penetrates the wood and leaves a lightly tinted appearance on the surface. INSTALLATION Refer to the SBC installation guide before starting a project. Download the SBC installation guide Make an informed choice Our experts will answer your technical or aesthetic questions. Contact an SBC expert LEEDI f4v.AnNLIFNIAI Ri31r•N SBC cedar shingtes could help you earn LEED® points. For more information, see our Whv SBC - Sustainability section on SBCCedar.com. RECEIVED APR 1. 4 2023 r AHMOU'i h1 LLSSBR U JIA VEY ■ ■. HARVEY WINDOWS + DOORS SECTION 08560 VINYL WINDOWS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2006 - 2022 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Vinyl windows for new construction. 1.2 RELATED SECTIONS A. Section 03300 - Cast -In -Place Concrete. B. Section 04810 - Unit Masonry Assemblies. C. Section 06100 - Rough Carpentry. D. Section 06200 - Finish Carpentry. E. Section 07460 - Siding. 1.3 REFERENCES 1 4 2023 +-rMOl17 h Ol_D KtNG'S HIGHWAY A. American Architectural Manufacturers Association (AAMA): 1. AAMAIWDMAICSA 10111.S.21A440-05, A440-08, A440-11 and A440-17 - NAFS - North American Fenestration Standard Specification for windows, doors, and skylights. 2. AAMA 7011702 - Combined Voluntary Specifications for Pile Weather strip and Replaceable Fenestration Weather seals. 3. AAMA 902 - Voluntary Specification for Sash Balances. B. ASTM International (ASTM): 1. ASTM E 283 - Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under Specified Pressure Differences Across the Specimen. 2, ASTM E 330 - Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls and Doors by Uniform Static Air Pressure Difference. 3, ASTM E 547 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Cyclic Static Air Pressure 08560-1 SFeEIVED Difference. APR 2023 4; ASTM E2190 - Standard Specification for the Classification of the Durability of YAhMUU1 t-1 Sealed Insulating Glass Units. OLD KiNG'S HIGHWAYS ASTResist nce of Window AssemF588 - Standard Testblies, Excods luding Glazing Imr Measuring the pact d Entry C. NFRC 100/200/500 - Procedures for Determining Fenestration Product U-Factors, Solar Heat Gain Coefficient (SHGc), and Visible Transmittance at Normal Incidence (VT). 1.4 SUBMITTALS A. Submit under provisions of Section 01300. B. Product Data: Submit the following documents for each type of window. 1. Manufacturer's technical data, product descriptions and installation guides. 2. Elevation for each style window specified indicating its size, glazing type, muntin type and design. 3. Manufacturer's head, jamb and sill details for each window type specified. C. Verification Samples: Operating units of each style window specified. 1. Verification samples may be operating scaled -down mock-ups of actual -size units. 2. Operating hardware such as balances, sash locks and weather-stripping. 3. Verification samples will be returned to manufacturer's representative at project closeout. D. Test Reports: Certified independent testing agency reports indicating window units meet or exceed specified performance requirements. 1.5 QUALITY ASSURANCE A. Manufacturer Qualifications: Minimum ten years producing vinyl (PVC) windows. B. Installer Qualifications: Minimum 2 years of experience on projects of similar size and acceptable to window manufacturer. C. Source Limitations: Obtain window units from one manufacturer through a single source. D. Testing: Provide window units independently tested and found to be in compliance with AAMA/WDMA/CSA 101/I.S.2/A440-05, A440-08, A440-11 or A440-1 i performance standards. E. Code Compliance: Provide windows that are labeled in compliance with the jurisdiction having authority in the location of the project. F. Mock -Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. 1. Finish areas designated by Architect. 2. Do not proceed with remaining work until workmanship and color are approved by Architect. 3. Rebuild mock-up area as required to produce acceptable work. 1.6 DELIVERY, STORAGE, AND HANDLING A. Deliver windows to project site in undamaged condition; handle windows to prevent damage to components and to finishes. 08560-2 03 --'/ l L4 RECEIVED j B. ;Store products in manufacturer's unopened packaging, out of direct sunlight or high APR 1 4 1'023 temperature locations, until ready for installation. rANV100I r� PROJECT CONDITIONS OLD ICING'S HIGHWAY A. Maintain environmental conditions (temperature, humidity and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits. PART 2 PRODUCTS 2.1 MANUFACTURERS A. Acceptable Manufacturer: Harvey Building Products , which is located at: 1400 Main St.; Waltham, MA 02451-1689; Toll Free Tel: 800-598-5400; Tel: 781-398-7800; Fax: 781-398-7749; Email: request info (arch itectsrc'D,harveybp.com); Web: hftps://www.harveywindows.com B. Requests for substitutions will be considered in accordance with provisions of Section 01600. Substitutions must be submitted to Architect two weeks prior to bid opening. 2.2 NEW CONSTRUCTION CLASSIC DOUBLE HUNG WINDOWS A. Construction: 1, Frame: 0.065 inch (1.7 mm) thick polyvinyl chloride (PVC) with miter cut and fusion welded corners. Sash: 0.060 inch (1.5 mm) thick polyvinyl chloride (PVC) with miter cut and fusion welded corners. 2. Glazing: Insulating glass units secured to sash frame using a silicone sealant and exterior glazing bead. Complies with ASTM E2190. 3. Sash Balances: Factory calibrated block and tackle, complying with AAMA-902. Balance cords shall be anchored to locking terminal housings when the sash is tilted in. The locking terminal and pivot bar system shall provide accurate alignment of the sash and the frame during operation. 4. Sash Locks: Cam type lock anchored with screws. Double locks when openings are 30 112 inches (774 mm) wide and greater. 5. Weather Stripping: In compliance with AAMA 701.2. B. Performance: 1. Forced Entry: Type B, Grade 10 in accordance with ASTM F 588. 3.1 EXAMINATION A, Verify rough opening size is of sufficient size to receive window unit and complies with manufacturer's requirements for opening clearances. Verify sill plate is level. B. Notify Architect of unacceptable conditions before proceeding with installation. 3.2 INSTALLATION A. Install window unit in accordance with manufacturer's printed instructions including the following: 1. Apply sealant around perimeter of window unit between nail fin and exterior sheathing of wall. Refer to Division 7 Section "Joint Sealants". 2. Install window unit square, level and plumb. Center window unit in opening and secure window unit by nailing through nail fin and screw through jambs 08560-3 a�,� as indicated in manufacturer's instructions. 3. Flash window in accordance with AAMA's "Standard Practice for Installation of Windows with a Mounting Flange in Stud Frame Construction". 4. Insulate between window frame and rough opening with insulation. Refer to Division 7 Section "Building Insulation". 3.3 ADJUSTING A. Adjust units for smooth operation without binding or racking. Adjust sash locks and screens for smooth operation. 3.4 CLEANING AND PROTECTION A. Clean soiled surfaces and glass prior to substantial completion. B. Protect window unit from damage until substantial completion. Repair or replace damaged units. 11ECE1VED APR 14 202? Y AHMOU l'i-1 OLD 'S HIGHWAY KING END OF SECTION 08560-4 9 THERMA-TRU Corp. 1750 Indian Wood Circle Maumee, OH 43537 Toll Free 800-891-7400 Phone 419-891-7400 Website www.thermatru.com FeeVIED APR 14 2023 YAHfUOW h Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat, and PageFormal. The section must be carefully reviewed and edited by the Architect to meet the requirements of the project and local building code. Coordinate this section with other specification sections and the Drawings. Delete all "Specifier Notes" when editing this section, Section numbers and titles are from MasterFormat 2011 Update. DIVISION 08 16 13 FIBERGLASS ENTRY DOORS Specifier Notes: This section covers Thernxa-Trut branded fiberglass entry door slabs ('Doors') and other components of the doors system which can be sourced through Therma-Tru*. Consult your local Therma-Tru Architectural Sales Specialist for assistance in editing this section for the specific application. PART GENERAL 1.1 SECTION INCLUDES A. Fiberglass Entry Doors B. Impact Resistant Fiberglass Entry Doors C. Fire Rated Fiberglass Entry Doors 1.2 RELATED SECTIONS Specifier Notes., Edit the following list of related sections as required for the project. List other sections with work directly related to this section. Verify section numbers and titles. A. 06 40 00 - Architectural Woodwork B. 07 27 00 — Air Barriers: Water-resistant barrier C. 07 92 00 — Joint Sealants: Sealants and caulking D. 08 80 00 - Glazing E. 08 7100 — Door Hardware F. 09 90 00 - Painting and Coating Fiberglass Entry Doors 08 16 13 RECEIVED APR 1. 4 2023 YAhlAUU 1 r, 1.3 REFERENCES Specifier Notes: Standards listed by reference including revisions by issuing authority. This article does not require compliance with standards, but is merely a listing of those that may be used. A. American Society for Testing and Materials (ASTM): 1. ASTM E 90 — Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions. 2. ASTM E 283 — Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under Specified Pressure Difference Across the Specimen. 3. ASTM E 330 — Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference. 4. ASTM E 331— Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference, 5. ASTM E 413 — Classification for Rating Sound Insulation (STC). 6. ASTM E 547 — Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure Difference, 7. ASTM E 1300 — Standard Practice for Determining Load Resistance of Glass in Buildings. 8. ASTM E 1332 — Standard Classification for Determination of Outdoor -Indoor Transmission Class. 9. ASTM E 1886 — Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missiles and Exposed to Cyclic Pressure Differentials. 10. ASTM E 1996 — Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes. 11. ASTM E 2235 — Standard Test Method for Determination of Decay Rates for Use in Sound Insulation Test Methods, B. California Reference Standard Code; 1. CA SFM 12-7A-1— Materials and Construction Methods for Exterior Wildfire Exposure. C. Canadian Standard: 1. CAN4-S104 — Standard Method for Firo Tests of Door Assemblies. D. Environmental Protection Agency and Department of Energy: 1. Energy Star Program Requirements Product Specification for Residential Windows, Doors, and Skylights. E. Code of Federal Regulations: 1. CFR 1201 Part 2 — Safety Standard for Architectural Glazing Materials, F. Florida High Velocity Hurricane Zone (HVHZ) Testing Application Standards: 1. TAS 201— Impact Test Procedures. 2. TAS 202 — Criteria for Testing Impact and Non -Impact Resistant Building Envelope Components Using Uniform Static Air Pressure. 3. TAS 203 — Criteria for Testing Products Subject to Cyclic Wind Pressure Loading. G. National Accreditation & Management Institute (NAMI) H. National Fenestration Rating Council 1. NFRC 100 — Procedure for Determining Fenestration Product U-Factors. Fiberglass Entry Doors 081613 a2-A(i!_ 2. NFRC 200 — Procedure for Determining Fenestration Product Solar Heat Gain Coefficient and Visible Transmittance (VT) at Normal Incidence. 3. NFRC 400 — Procedure for Determining Fenestration Product Air Leakage. CEIVED I. National Fire Protection Association 1. NFPA 252 — Standard Methods of Fire Tests of Door Assemblies APR 14 2023 J. Underwriters Laboratory I Af1MUU ! r, 1. UL 1013 — Standard for Fire Testing Door Assemblies. U!_U KING'S HIGHWAY 2. UL IOC — Standard for Positive Pressure Fire Tests of Door Assemblies, 1.4 PERFORMANCE REQUIREMENTS Specifier Notes: Performance ratings for doors vary by product, configuration, and size. Current performance information is found at www.thermatru.com. Consult your local Therma-Tru Architectural Sales Specialist for more information. Delete the following performance requirements if not required. A. Doors shall have a structural design pressure rating of DP [ ], B. Doors shall have an impact design pressure rating of DP [ ` ]. C. Door Unit Air Leakage, NFRC 400, 1.57 psf (25 mph): 0.50 cfm per square foot of frame or less. D. Door Unit Water Penetration: No water penetration through door unit when tested in accordance with ASTM E 331or ASTM E 547 with water applied at rate of 5 gallons per hour per square foot at 0 psf. E. Doors shall have a minimum STC rating of [ _ ] or a minimum OITC rating of F. Doors shall have a positive pressure certified fire door rating of [ _ ] minutes. G. Doors shall have a minimum/maximum U-Value of [ ] and a minimum/maximum SHGC of H. Doors shall qualify for Energy Star Rating. 1.5 SUBMITTALS A. Refer to Division 0133 00 Submittal Procedures [Insert division number and title]. B. Product Data: Submit door manufacturer current product literature, including installation instructions. C. Shop Drawings: Submit manufacturer's shop drawings, indicating dimensions, construction, component connections, anchorage methods and locations, accessories, hardware locations, and installation details. D. Samples: Submit full-size or partial full-size verification sample of door illustrating glazing system, quality of construction, texture, and color of finish. Fiberglass Entry Doors 08 16 13 FcF-iV GD APR 14 2023 Y AhIVIUU I t-- 1.6 QUALITY ASSURANCE A. Mockup: 1, Provide sample unit of representative product size and using manufacturer approved installation methods to determine acceptability of door installation methods. Comply with Division 0143 39 Quality Assurance 2. Approved mockup shall represent minimum quality required for the Work. Approved mockup shall [not] remain in place within the Work. C. Quality Assurance Submittals: 1. Provide documentation for specified performance as required. 2. Manufacturers' installation instructions. D. Manufacturer Qualifications: Manufacturer shall have successful experience in producing the type of product required for project applications equivalent to the requirements for this project. specifier notes: Therma-Tru manufactures fiberglass door slabs and related components and sources them to distributor and dealer fabricators for system assembly. Fabricators will have successful experience in producing the type of product required equivalent to the project requirements. E. Installer Qualifications: 1, [optional: Installer holds current credential as a NAMI Certified Installer of Therma- Tru Side Hinged Door Installations and as a Therma-Truo Certified Installer.] 1.7 DELIVERY, STORAGE, AND HANDLING A. Refer to Division 0160 00 Product Requirements. B. Delivery: Deliver materials to site undamaged with labels clearly identifying manufacturer, product name, and installation instructions C. Storage: Store materials in an upright position, off ground, under cover, and protected from weather, direct sunlight, and construction activities. D. Handling: protect materials and finish during handling and installation to prevent damage. 1.8 WARRANTY A. Refer to Division 0178 36 Warranties B. Therma-Trur, standard limited warranty for fiberglass Therma-Tru® Door Product and genuine Therma-Tru* components, including rot -resistant frames, mullions, and brickmould sourced from Therma-Tru (excluding primed pine door frames and oak door Fiberglass Entry Doors 08 16 13 frames, and non -rot resistant mullions and brickmould) used in commercial and multi - residential projects will be free from material and workmanship defects for a period of three years subject to certain limitations and restrictions. For complete details and current warranty information go to www.thermatru.com. PART 2 PRODUCTS 2.1 MANUFACTURER A. Basis of design: Therma-Tru Corp. 1750 Indian Wood Circle Maumee, OR 43537 (419) 891-7400 (800) 843-7628 www.therrnatru.com Contact: Rod Clark 458-206-8532 rclark@thermatru.com RECEIVED APR 14 2023 fAHI rOu i r, B. Substitutions: Not permitted C. Requests for substitutions will be considered in accordance with provisions of Division 01 6000. 2.2 A. FIBERGLASS ENTRY DOORS Fiberglass Entry Doors: All fiberglass doors manufactured by Therma-Trus. Specification is for complete entry systems with components manufactured by Therma-True and assembled by independent fabricators. 1. Select [Classic-Crafth], [Fiber-Classic]o, [Smooth -Star,], [20 Min Fire Door] 2. Construction: a. Classic -Craft& 3/32" minimum thickness proprietary fiberglass reinforced thermoset composite, "AccuGrain" textured to duplicate hand-crafted hardwood master or smooth surface. Door edges are machinable kiln -dried hardwood, flush and square with door faces, lock edge reinforced with full-length integrated 3-1/2-inch wide engineered lumber core. Door bottom edge is moisture- and decay -resistant composite. Core is foamed - in -place polyurethane, with a minimum density of 1.9 pef. b. Fiber -Classic, 1/16-inch minimum thickness, proprietary fiberglass -reinforced thermoset composite, wood -grained in natural hardwood patterns, stainable and paintable. Fiberglass Entry Doors 081613 33 ;, . Door edges are machinable kiln -dried pine, primed, lock edge reinforced with engineered lumber core, lockset area reinforced with solid blocking for hardware backup. Door bottom edge is moisture- and decay -resistant composite. Core is foamed -in -place polyurethane, density 1.9 pcf minimum. C. Smooth Star inforced thermoset 111 inch minimum thickness, proprietary fiberglass-re composite, surface lightly textured. Door edges are machinable kiln -dried pine, primed, lock edge reinforced with engineered lumber core, lockset area reinforced with solid blocking for hardware backup. Door bottom edge is moisture- and decay - resistant composite. Core is foamed -in -place polyurethane, density 1.9 pcf minimum. 3. Door Style a. Classic -Crafter 1. American Collection: Enter Style Number [ _ ]•RFCF VC 2. Mahogany Collection: Enter Style Number [ ]. 3. Rustic Collection: Enter Style Number [ ]L APR 1 4 2023 4. Oak Collection: Enter Style Number [ ]. 5. Canvas Collection: Enter Style Number [ ]. r�niti�� c1l h G KfNG'S HIGFN ,4 b. Fiber -Classic* 1. Mahogany Collection: Enter Style Number [ ]. 2. Oak Collection: Enter Style Number [ ] c. Smooth -Stare 1. Enter Style Number [ ]. B. Frames: Provided and assembled by third party fabricators to exacting specifications from Therma Tru to help maximize system performance. Therma-Truo strongly recommends the use of rot - resistant frames, mullions, and brickmould sourced from Therma-Tru, however, the use of a non Therma-Tru® frame system (or a Therma-Tru Primed Pine Frame or Therma-Tru Oak Frame) will not automatically void the entire limited warranty. Refer to 1.8.B for clarification. 1. Milled from 514 kiln -dried material with profiled Y2" stop and 6 degree sill gain prep. 2. Jamb Width [Standard 4 9/16"] Optional: [5 '/"] [6 9116] 3. Rot Resistant — frames, mullions, and brickmould sourced through Therma-Tru. C. Sills 1. Inswing: [Composite Adjustable] [Hardwood Adjustable] [Basic Fixed] [Basic Composite Adjustable] [Moderate Climate] 2. Outswing: [Composite Outswing] [Aluminum with Thermal Break] [Aluminum No Thermal Break] [Coastal] 3. Other: [Public Access Sill] 4. Finish: [Mill] [Bronze] [Brass] [Satin nickel] 2.3 HARDWARE Fiberglass Entry Doors 08 16 13 Specifier Notes: Fiberglass entry doors are available with optional Therma-Tru factory installed multi -point lock; prepped for standard locking hardware; or no bore. A. Hinges: Steel, [optional ball bearing] 4 x 4 x 0.098 inches finished to match hardware, plated screws to match 1. Finish: [US4, Zinc dichromate] [US3, bright brass] [US5, antique brass] [US 15, brushed nickel] [US17A, black nickel] [US15A, antique nickel] [US26, polished chrome] [US10B, oil rubbed bronze] [US32D stainless steel] Specifier Notes: Multi point locking system is optional. Delete if not required. B. Locking Hardware: 1. Multi -point lock system includes stainless steel face plate. 2. Multi -point lock system handle set hardware: [Heirloom] [Venture] [Millennium] [Ara] [Decade] 3. Finish: [US3, bright brass] [US5, antique brass] [US15, brushed nickel] [US 17A, black nickel] [US15A, antique nickel] [US26, polished chrome] [US10B, oil rubbed bronze] [BY, white] Specifier Notes: Decorative and specialty glass is standard and included with the select model numbers. 2.4 GLAZING 1. Therma-Tru factory glazed with [double -pane] or [triple -pane] construction. 2. [Decorative] [Specialty] designated by door model number. 3. Privacy glass: [Chord] [Rain] [Chinchilla] [Granite] 2.5 INSTALLATION ACCESSORIES A. Sill pan B. Corner seal pad C. Rain deflector D. Rain Guard PART 3 EXECUTION 3.1 EXAMINATION RECEIVE® APR 14 2023 f mmiviuu i ri A. Examine areas to receive doors. Notify Architect in writing any unacceptable conditions that would adversely affect installation or subsequent performance of the product. Do not proceed with installation until unsatisfactory conditions are corrected. 3.2 INSTALLATION Fiberglass Entry Doors 081613 A. Install fiberglass doors in full compliance with Therma-Trua,, written instructions and approved shop drawings. B, Install 20 minute: doors with permanent fire door certification label in compliance with the requirements of the labeling agency and NFPA. C. Maintain alignment and compatibility with adjacent work. 3.3 FINISHING A, Finish in compliance with Therma-True written recommendations. Guidance for proper finishing is available at www.therrnatru.com — "Recommendations for Proper Finishing and Painting or Staining." 3.3 Protection A. Protect installed products until completion of project. B. Touch-up, repair or replace damaged products prior to Substantial Completion in accordance with Therma-Tru written recommendations. Guidance for proper finishing is available at www.thermatru.com — "Recommendations for Proper Finishing and Painting or Staining." PFC-1 �D APR 14 20" f OLD K N 'S H1gG AY END OF SECTION Fiberglass Entry Doors 08 16 13