The URL can be used to link to this page

Home My WebLink About480 BUCK ISLANDELECTRICAL & GROUNDING NOTES 1. ALL ELECTRICAL WORK SHALL CONFORM TO THE REQUIREMENTS OF THE NATIONAL ELECTRICAL CODE (NEC) AS WELL AS APPLICABLE STATE AND LOCAL CODES. 2. ALL ELECTRICAL ITEMS SHALL BE U.L. APPROVED OR LISTED AND PROCURED PER SPECIFICATION REQUIREMENTS. 3, THE ELECTRICAL WORK INCLUDES ALL LABOR AND MATERIAL DESCRIBED BY DRAWINGS AND SPECIFICATION INCLUDING INCIDENTAL WORK TO PROVIDE COMPLETE OPERATING AND APPROVED ELECTRICAL SYSTEM, 4. GENERAL CONTRACTOR SHALL PAY FEES FOR PERMITS, AND IS RESPONSIBLE FOR OBTAINING SAID PERMITS AND COORDINATION OF INSPECTIONS, 5. ELECTRICAL AND TELCO WIRING AT EXPOSED INDOOR LOCATIONS SHALL BE IN ELECTRICAL METALLIC TUBING OR RIGID NONMETALLIC TUBING (RIGID SCHEDULE 40 PVC OR RIGID SCHEDULE 80 PVC FOR LOCATIONS SUBJECT TO PHYSICAL DAMAGE) (AS PERMITTED BY CODE). 6. ELECTRICAL AND TELCO WIRING AT CONCEALED INDOOR LOCATIONS SHALL BE IN ELECTRICAL METALLIC TUBING, ELECTRICAL NONMETALLIC TUBING, OR RIGID NONMETALLIC TUBING (RIGID SCHEDULE 40 PVC AS PERMITTED BY CODE). 7. ELECTRICAL AND TELCO WIRING OUTSIDE A BUILDING, ABOVE GRADE AND EXPOSED TO WEATHER SHALL BE IN WATER TIGHT GALVANIZED RIGID STEEL CONDUITS (RGS) AND WHERE REQUIRED IN LIQUID TIGHT FLEXIBLE METAL OR NONMETALLIC CONDUITS. S. BURIED CONDUIT SHALL BE RIGID NONMETALLIC CONDUIT (RIGID SCHEDULE 40 PVC); DIRECT BURIED IN AREAS OF OCCASIONAL UGHT TRAFFIC, ENCASED IN REINFORCED CONCRETE IN AREAS OF HEAVY TRAFFIC. 9. LIQUID —TIGHT FLEXIBLE METALLIC CONDUIT SHALL BE USED INDOORS AND OUTDOORS IN AREAS WHERE VIBRATION OCCURS AND FLEXIBILITY IS NEEDED. 10. ELECTRICAL WIRING SHALL BE COPPER WITH TYPE THHN, THWN-2, OR THIN INSULATION. 11. RUN ELECTRICAL CONDUIT OR CABLE BETWEEN ELECTRICAL UTILITY DEMARCATION POINT AND PROJECT OWNER CELL SITE PPC AS INDICATED ON THIS DRAWING. PROVIDE FULL LENGTH PULL ROPE. COORDINATE INSTALLATION WITH UTILITY COMPANY. 12. RUN TELCO CONDUIT OR CABLE BETWEEN TELEPHONE UTILITY DEMARCATION POINT AND PROJECT OWNER CELL SITE TELCO CABINET AND BTS CABINET AS INDICATED ON THIS DRAWING. PROVIDE FULL LENGTH PULL ROPE IN INSTALLED TELCO CONDUIT. PROVIDE GREENLEE CONDUIT MEASURING TAPE AT EACH END. 13. ALL EQUIPMENT LOCATED OUTSIDE SHALL HAVE NEMA 3R ENCLOSURE. 14. GROUNDING SHALL COMPLY WITH NEC ART. 250. ADDITIONALLY, GROUNDING, BONDING AND LIGHTING PROTECTION SHALL BE DONE IN ACCORDANCE WITH METRO MOD CELL SITE GROUNDING STANDARDS. 15. GROUND CABLE SHIELDS MINIMUM AT BOTH ENDS USING MANUFACTURERS CABLE GROUNDING KITS SUPPLIED BY PROJECT OWNER. IS. USE #6 COPPER STRANDED WIRE WITH GREEN COLOR INSULATION FOR ABOVE GRADE GROUNDING (UNLESS OTHERWISE SPECIFIED) AND #2 SOLID TINNED BARE COPPER WIRE FOR BELOW GRADE GROUNDING AS INDICATED ON THE DRAWING. 17. ALL POWER AND GROUND CONNECTIONS TO BE CRIMP —STYLE, COMPRESSION WIRE LUGS AND WIRE NUTS BY HARGER (OR APPROVED EQUAL) RATED FOR OPERATION AT NO LESS THAN 75'C OR CADWELD EXOTHERMIC WELD. DO NOT ALLOW BARE COPPER WIRE TO BE IN CONTACT WITH GALVANIZED STEEL 18. ROUTE GROUNDING CONDUCTORS ALONG THE SHORTEST AND STRAIGHTEST PATH POSSIBLE, EXCEPT AS OTHERWISE INDICATED. GROUNDING LEADS SHOULD NEVER BE BENT AT RIGHT ANGLE. ALWAYS MAKE AT LEAST 12' RADIUS BENDS. #6 WIRE CAN BE BENT AT 6" RADIUS WHEN NECESSARY. BOND ANY METAL OBJECTS WITHIN 6 FEET OF PROJECT OWNER EQUIPMENT OR CABINET TO MASTER GROUND BAR OR GROUNDING RING. 19. CONNECTIONS TO GROUND BARS SHALL BE MADE WITH TWO HOLE COMPRESSION TYPE COPPER LUGS. APPLY OXIDE INHIBITING COMPOUND TO ALL LOCATIONS. 20. APPLY OXIDE INHIBITING COMPOUND TO ALL MECHANICAL GROUND CONNECTIONS. 21. CONTRACTOR SHALL PROVIDE AND INSTALL OMNI DIRECTIONAL ELECTRONIC MARKER SYSTEM (EMS) BALLS OVER EACH GROUND ROD AND BONDING POINT BETWEEN EXISTING TOWER/ MONOPOLE GROUNDING RING AND EQUIPMENT GROUNDING RING, 22,CONTRACTOR SHALL TEST COMPLETED GROUND SYSTEM AND RECORD RESULTS FOR PROJECT CLOSE—OUT DOCUMENTATION. 5 OHMNS MINIMUM RESISTANCE REQUIRED. 23. CONTRACTOR SHALL CONDUCT ANTENNA, CABLE, AND LNA RETURN —LOSS AND DISTANCE —TO —FAULT MEASUREMENTS (SWEEP TESTS) AND RECORD RESULTS FOR PROJECT CLOSE OUT. 24. THE T—MOBILE ELECTRICAL EQUIPMENT INCLUDING PANEL, SWITCH GEAR AND DISCONNECT ARE TO BE LABELED WITH ENGRAVED BAKELITE LABELS. GROUNDING LEGEND A COMPRESSION FITTING CONNECTION EXOTHERMIC WELD CONNECTION --- PROPOSED GROUND WIRING ------------ EXISTING GROUND WIRING GAMMA BETA ALPHA TOTALLY �..,. COMMITTED Z Cj NO-C ENGINEERING SERVICES, LLC, Z IN A—.o DRw tlT H" FORD, W 01124 Q IFrl19ft- C14 Uq ��nn� oZ Ng z ?,ter oW �w pZof U''k" 00� Or �Q We a7d a7d' I�u�t a7d' a7d uQ IL� a =il{❑ G ❑LS LL��I� ❑ ❑ ❑ z T-MOBILE NORTHEAST LLC r � RRU r 15 COMMERCE WAY, SUITE B i RRU RRU ` 1 / r NORTON, MA 02766 OFFICE: (508) 286-2700 T/aA r i % r I \ FAX: (508) 286-2893 I � A 4HY0542A A HY542 / YARMOUTH WT 6 WIRE TO GS ( ) 6 WIRE TO [ 480 BUCK ISLAND ROAD # ° ° ° °°°/, ROUND BAR TYP GROUND BAR (TYP) LL °.°°"°°° GROUND BAR (TYP) "°° " `°° "°°°°°°°°° WEST YARMOUTH, MA 02673 EXISRNG SECTOR BARNSTABLE COUNTY _ EXI57NG SECTOR EXISnNG SECTOR GROUND FAR GROUIJD c3AR GROUND BAR 1 ANTENNA GROUNDING DETAIL REVISIONS — G 1 NTS z O R aizvle PERMiTnNc cos cw A 05,22119 PRELIMINARY CDs ALI TYPE TA TYPE VB 2 G-1 TYPE VN TYPE NO TYPE SS TYPE W TYPE VS TYPE PT TYPE GT TYPE GY TYPE GR TYPE GL CADWELD GROUNDING CONNECTION DETAILS NTS REV DATE DESCRIPTION B` .- RFGrstE�Y� j2AWG WITH LONG BARREL COMPRESSION LUGS, USE STAR WASHERS, LOCKWASHERS, AND STAINLESS STEEL HARDWARE TO SECURE TO EXTERNAL GROUND BAR BY GENERAL CONTRACTOR. NEW COAXIAL GROUND KITS WITH LONG BARREL COMPRESSION LUGS WITH TWO (2) F3/8"4 BOLTS AND LOCK WASHERS SIMILAR TO ANDREW 3241088-9. 2 STAINLESS STEEL HARDWARE .1� I KRUPAKARAN KOLANDAIVELU,P.E. TWO HOLE COPPER 0 MA PROFESSIONAL ENGINEER LTC. #50019 COPPER GROUND BAR COMPRESSION TERMINAL a o RS (tYP) GROUNDING CABLE A a o........... 000oDo°D /K` GROUND BAR — ELEY9i� a_ i �. 00 0000 00000 6" MIN. o STAR WASHER (iYP) -- FLAT WASHER (TYP) u� �—Vx%* HEX BOLT GROUNDING MIT (TIP)--- 1)_,% 02 BARE SOUR -TINNED COPPER CONDUCTOR TO GROUND BUS. GROUND BAR DETAILS NOTES: GROUNDING CABLE - —EXPOSED BARE COPPER TO BE KEPT TO `n 1. ALL HARDWARE STAINLESS STEEL COAT ALL SURFACES WITH KOPR-SHIELD SECTION "A -A ABSOLUTE MINIMUM, NO INSULATION ALLOWED BEFORE MATING. WITHIN THE COMPRESSION TERMINAL (1YP.) 2, FOR GROUND BOND TO STEEL ONLY: INSERT A TOOTH WASHER BETWEEN NOTES: LUG AND STEEL, COAT ALL SURFACES WITH KOPR-SHIELD. 3. ALL HOLES ARE COUNTERSUNK X/ 1. OXIDE INHIBITING COMPOUND TO BE USED AT ALL LOCATIONS. �J z 3 GROUNDING BAR CONNECTIONS G 1 NTs ----- Gml ?